Barista Exchange

the world's premiere online community for the specialty coffee industry

hey all, i installed my new (to me) 3 group semi-auto gb/5 tonight, and while the shots were pulling fine, the vacuum breaker on the steam boiler continued to hiss at a medium volume until i shut the machine off and bled the pressure off. does the gasket or teflon thingy in the breaker need to be replaced? is the gasket easy to find at a hardware shop? counter culture used to service it, i'm going to call them tomorrow but any help would be much appreciated.

other than that, this machine slays tho. i easily pulled the best shots i've had in ages without the grinder even being dialed in.

Share

Reply to This

Replies to This Discussion

A bit of scale or other crud may have gotten in the breaker valve during shipping. It's supposed to close when the pressure rises. Sometimes just fiddling with it (carefully tapping it 'cuz it hot!) while under pressure will get it to seal. Could be the gasket but I doubt it, unless you saw steam escaping from around the gasket of course. Did you take the cover off to see where the steam hiss was coming from?

Reply to This

you mean the grate the cups sit on? yeah. straight out of the vacuum breaker valve, around the little post. i pushed it in and out while the machine was bleeding out, and it still kept leaking. are they easy to take apart and inspect once the machine is cooled?

Reply to This

I've never successfully got one to work properly again after it quit working properly if cleaning descaling didn't do it. I'd just replace it, ~20 shipped. http://www.espressoparts.com/W10836

Anything is easy if you know how. Everything is hard if you don't! For me it wouldn't be worth investing much time or effort, too many other things to do...

Reply to This

Those Vac-breaks always do that. Before you order more parts turn the unit on and follow Mike's advice of carefully fiddling with it while the machine has full pressure. Pretty much every one of those I've ever changed has done that hissing/leaking for the first little bit. It might be that the rubber seal needs to get a little hot and plyable before it seals. (Assuming that the part is new). If the part is the typical LM piece then all you need are two wrenches to get it apart. There is just a basic rubber o-ring on top of the piston which you can inspect and you can just twist it back together if you don't see any debris. Watch out for the copper crush washer when you take it off, be sure to save it. Use teflon tape when you put it back on. It's pretty easy/straightforward.

Reply to This

the o-ring was dry-rotted. got a ten pack of number 80 o-rings at Lowes for two bones. fixed the hiss immediately. thanks all!

Reply to This

you have a gb5 yet your cutting corners??? it is a saftey device and when need be you'll want it to work right either that or you'll see the milk disappear from the pitcher your steaming haha, not always but it does happen.
just replace it you'll be better off that way. also if that one was hissing i'd replace the opv as well if you really had that much scale and it sounds like your dealing with a used machine?? if you can disassemble it im sure you could do either of those two things with out counter cultures or anyone's help its very easy turn off machine open steam valves till no more steam crescent wrench and teflon tape prefer the pink stuff its thicker remember put tape on with the threads(i know some dont use tape but I do there is a little brass/copper washer) and bam your done take you longer to bleed the boiler than to install just dont over tighten cause then YOUR SCREWED!!!

Reply to This

sry mike you covered a lot of that didnt read your post if you use tape you dont always need the crush washer (if you lose it)

Reply to This

yeah i called imperial service in statesville (the only close LM service reps) and they said to just put a new o-ring on it, which i did. teflon taped too. also bill - holy run-on sentence batman. use some commas bro.

Reply to This

i fix espresso machines im not an engrish teacher

Jared Rutledge said:
yeah i called imperial service in statesville (the only close LM service reps) and they said to just put a new o-ring on it, which i did. teflon taped too. also bill - holy run-on sentence batman. use some commas bro.

Reply to This

Jared Rutledge said:
yeah i called imperial service in statesville (the only close LM service reps) and they said to just put a new o-ring on it, which i did. teflon taped too. also bill - holy run-on sentence batman. use some commas bro.

I'm with Bill here. Replace the whole thing (including the copper washer) - $20 and 15 minutes worth of work, tops. Wish I'd seen this earlier, I'd have asked the Dripolator guys to take one back with them today. I do have one on hand, let me know if you want it.

BTW, is Imperial really still authorized to do LM service? I was under the impression that they just did Bunn and other drip. I'd take their espresso machine service advice with a grain of salt, based on some stuff I've seen and heard.

Reply to This

yeah they are. richard geldart from Franke (marzocco's US importer) told me that in April at the WBC. i guess it might have changed since then, but i dunno. i'll get a rebuild kit in the next week or so anyways (to have on hand) but the issue with the vacuum breaker was just the o-ring.

Reply to This

Jared Rutledge said:
yeah they are. richard geldart from Franke (marzocco's US importer) told me that in April at the WBC. i guess it might have changed since then, but i dunno...

Duly noted.

Reply to This

Reply to This

RSS

Sign in

E-mail

Password
 or Sign Up
By signing in, you agree to the amended Terms of Service and Privacy Policy.
Forgotten your password?

Latest Activity

barista Dan added a photo
5 minutes ago
I want to clarify.... Were you using My Chai, inc. from Bend, Or? Or some other my chai, or maya chai?
9 minutes ago
I'm not sure if you're looking for different importers/ roasters, but I know that Cafe Imports has a great deal of information on most all coffee they carry. I'm not sure if they offer there coffee roasted already or if its all green.
11 minutes ago
barista Dan is in the middle of the crunch season with Travelin Joe Espresso. Happy Holidays to all.
17 minutes ago
Tara Shenson is now friends with Coffee Slingers and Jane Barnes
17 minutes ago
20 minutes ago
I'll have to look into this Big Train Chai...I actually placed an order for a couple different kinds from Third Street Chai in Colorado so i'll have to let you know how they are! I should be getting them today or tomorrow.
21 minutes ago
Ty Paluska and Jill Zimmerman are now friends
26 minutes ago
IMHO a machine featuring saturated groups is ultimately what you should be shooting for. Though I wouldn't put up a humongous investment on one initially because there are a LOT of indie-type start up coffee shops coming up right now and the probabi…
27 minutes ago
Keaton Ritchie and Ruth Hall are now friends
30 minutes ago
Red Leaf Coffee Co. added a gift to their profile page
From the Gift Store
33 minutes ago
So how did the Experts give you an education while you were there? We are looking to do something like that realizing most of our customers know zero about espresso and zero about organic coffee. We are in a drive thru setting and wondered if we sho…
36 minutes ago
I would expect the market there would be good. A lot of the oil expats I know here in Indonesia have come via the oil business in Nigeria- along with manufacturers such as Cussons, Glaxo etc. I do understanf though that doing business in Nigeria is…
38 minutes ago
That is truly amazing. You will be blessed for your efforts!
41 minutes ago
Intelligentsia has so little information on offer about their Sidama right now because it's this years crop and the Ethipian Commodity Exchange has really been wreaking havoc with all of the work a lot of quality oriented roasters have put into trac…
43 minutes ago
Jeff Jaworski updated their profile
44 minutes ago

bX Job Postings

Jobs

Post a Job! $10 for 30 days

Click here to order your Barista Exchange T-Shirt!

© 2009   Created by Matt Milletto

Badges  |  Report an Issue  |  Privacy  |  Terms of Service

Sign in to chat!